 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MICROWAVE CORPORATION v01.0803 HMC339 GaAs MMIC SUB-HARMONICALLY PUMPED MIXER, 33 - 42 GHz Features Integrated LO Amplifier: +2 dBm Input Sub-Harmonically Pumped (x2) LO High 2LO/RF Isolation: > 37 dB Small Size: 0.81mm x 1.32mm Typical Applications The HMC339 is ideal for: * 33 to 42 GHz Microwave Radios * Up and Down Converter for Point to Point Radios * Satellite Communication Systems Functional Diagram General Description The HMC339 chip is a sub-harmonically pumped (x2) MMIC mixer with an integrated LO amplifier which can be used as an upconverter or downconverter. The chip utilizes a GaAs PHEMT technology that results in a small overall chip area of 1.07mm2. The 2LO to RF isolation is excellent eliminating the need for additional filtering. The LO amplifier is a single bias (+3V to +4V) two stage design with only +2 dBm nominal drive requirement. All data is measured with the chip in a 50 ohm test fixture connected via 0.025mm (3 mil) ribbon bonds of minimal length <0.31 mm (<12 mils). 5 MIXERS - CHIP Electrical Specifications, TA = +25 C, As a Function of Vdd Parameter IF = 1 GHz LO = +2 dBm & Vdd = +4V Min. Frequency Range, RF Frequency Range, LO Frequency Range, IF Conversion Loss Noise Figure (SSB) 2LO to RF Isolation 2LO to IF Isolation IP3 (Input) 1 dB Compression (Input) Supply Current (Idd) 27 30 5 -4 Typ. 33 - 42 16.5 - 21 DC - 3 10 10 37 40 10 0 28 13 13 23 25 3 -5 Max. IF = 1 GHz LO = +2 dBm & Vdd = +3V Min. Typ. 33 - 38 16.5 - 19 DC - 3 10 10 37 40 8 -1 25 12 12 Max. GHz GHz GHz dB dB dB dB dBm dBm mA Units *Unless otherwise noted, all measurements performed as downconverter, IF= 1 GHz. 5 - 110 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v01.0803 MICROWAVE CORPORATION HMC339 GaAs MMIC SUB-HARMONICALLY PUMPED MIXER, 33 - 42 GHz Conversion Gain vs. Conversion Gain vs. GaAs MMIC = +2 dBm, Vdd= +4V SUB-HARMONICALLY TemperatureMIXER +2 dBm, Vdd= +3V PUMPED @ LO = 17 - 25 GHz Temperature @ LO 0 + 25 C 0 + 25 C + 85 C - 55 C CONVERSION GAIN (dB) + 85 C - 55 C -8 CONVERSION GAIN (dB) -4 -4 -8 -12 -12 -16 -16 -20 30 31 32 33 34 35 36 37 38 39 40 41 42 FREQUENCY (GHz) -20 30 31 32 33 34 35 36 37 38 39 40 41 42 FREQUENCY (GHz) 5 MIXERS - CHIP Conversion Gain vs. LO Drive @ Vdd = +4V 0 0 dBm + 2 dBm + 4 dBm Conversion Gain vs. LO Drive @ Vdd = +3V 0 0 dBm + 2 dBm + 4 dBm CONVERSION GAIN (dB) -8 CONVERSION GAIN (dB) 42 -4 -4 -8 -12 -12 -16 -16 -20 30 31 32 33 34 35 36 37 38 39 40 41 FREQUENCY (GHz) -20 30 31 32 33 34 35 36 37 38 39 40 41 42 FREQUENCY (GHz) Isolation @ LO = +2 dBm, Vdd = +4V 10 0 LO/RF LO/IF RF/IF Isolation @ LO = +2 dBm, Vdd = +3V 10 0 LO/RF LO/IF RF/IF ISOLATION (dB) -20 -30 2LO/RF -40 ISOLATION (dB) -10 -10 -20 -30 2LO/RF -40 2LO/IF 2LO/IF -50 -60 30 31 32 33 34 35 36 37 38 39 40 41 42 FREQUENCY (GHz) -50 -60 30 31 32 33 34 35 36 37 38 39 40 41 42 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 5 - 111 MICROWAVE CORPORATION v01.0803 HMC339 GaAs MMIC SUB-HARMONICALLY PUMPED MIXER, 33 - 42 GHz Input IP3 vs. LO Drive @ Vdd = +4V* 20 Input IP3 vs. LO Drive @ Vdd = +3V* 20 THIRD ORDER INTERCEPT (dBm) 16 0 dBm + 2 dBm + 4 dBm THIRD ORDER INTERCEPT (dBm) 16 0 dBm + 2 dBm + 4 dBm 12 12 8 8 4 4 5 MIXERS - CHIP THIRD ORDER INTERCEPT (dBm) 0 33 34 35 36 37 38 39 40 41 FREQUENCY (GHz) 0 33 34 35 36 37 38 39 40 41 FREQUENCY (GHz) Input IP3 vs. Temperature @ LO = +2 dBm, Vdd = +4V* 20 + 25 C + 85 C - 55 C Input IP3 vs. Temperature @ LO = +2 dBm, Vdd = +3V* 20 THIRD ORDER INTERCEPT (dBm) 16 16 + 25 C + 85 C - 55 C 12 12 8 8 4 4 0 33 34 35 36 37 38 39 40 41 FREQUENCY (GHz) 0 33 34 35 36 37 38 39 40 41 FREQUENCY (GHz) Input IP2 vs. LO Drive @ Vdd = +4V* 70 Input IP2 vs. LO Drive @ Vdd = +3V* 70 SECOND ORDER INTERCEPT (dBm) 60 50 40 30 20 10 0 33 34 35 36 37 38 39 0 dBm + 2 dBm + 4 dBm SECOND ORDER INTERCEPT (dBm) 60 50 40 30 20 10 0 0 dBm + 2 dBm + 4 dBm 40 41 33 34 35 36 37 38 39 40 41 FREQUENCY (GHz) FREQUENCY (GHz) * Two-tone input power = -10 dBm each tone, 1 MHz spacing. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 5 - 112 MICROWAVE CORPORATION v01.0803 HMC339 GaAs MMIC SUB-HARMONICALLY PUMPED MIXER, 33 - 42 GHz Input IP2 vs. Temperature @ LO = +2 dBm, Vdd = +4V* 70 Input IP2 vs. Temperature @ LO = +2 dBm, Vdd = +3V* 70 SECOND ORDER INTERCEPT (dBm) 60 50 40 30 20 10 0 33 34 35 36 37 38 39 SECOND ORDER INTERCEPT (dBm) + 25 C + 85 C - 55 C 60 50 40 30 20 10 0 + 25 C + 85 C - 55 C 40 41 33 34 35 36 37 38 39 40 41 FREQUENCY (GHz) FREQUENCY (GHz) 5 MIXERS - CHIP Input P1dB vs. Temperature @ LO = +2 dBm, Vdd = +4V 10 8 6 4 Input P1dB vs. Temperature @ LO = +2 dBm, Vdd = +3V 10 8 6 4 + 25 C + 85 C - 55 C P1dB (dBm) 2 0 -2 -4 -6 -8 -10 34 35 36 37 38 39 40 FREQUENCY (GHz) + 25 C + 85 C - 55 C P1dB (dBm) 2 0 -2 -4 -6 -8 -10 34 35 36 37 38 39 40 FREQUENCY (GHz) RF & LO Return Loss @ LO = +2 dBm, Vdd = +4V 0 IF Return Loss @ LO = +2 dBm, Vdd = +4V 0 RETURN LOSS (dB) -10 RETURN LOSS (dB) -5 -5 -10 -15 LO RF -15 IF -20 0 5 10 15 20 25 30 35 40 FREQUENCY (GHz) -20 0 1 2 3 4 5 6 7 8 9 10 FREQUENCY (GHz) * Two-tone input power = -10 dBm each tone, 1 MHz spacing. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 5 - 113 v01.0803 MICROWAVE CORPORATION HMC339 GaAs MMIC SUB-HARMONICALLY PUMPED MIXER, 33 - 42 GHz IF Bandwidth @ LO = +2 dBm 0 Vdd= +3V Vdd= +4V Upconverter Performance Conversion Gain, LO = +2 dBm, Vdd = +4V 0 Vdd= +4V Vdd= +3V CONVERSION GAIN (dB) -8 CONVERSION GAIN (dB) 5 -4 -4 -8 -12 -12 -16 -16 5 MIXERS - CHIP -20 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 FREQUENCY (GHz) -20 26 28 30 32 34 36 38 40 42 FREQUENCY (GHz) Absolute Maximum Ratings RF / IF Input (Vdd = +5V) LO Drive (Vdd = +5V) Vdd Continuous Pdiss (Ta = 85 C) (derate 2.64 mW/C above 85 C) Storage Temperature Operating Temperature +13 dBm +13 dBm +5.5V 238 mW -65 to +150 C -55 to +85 C MxN Spurious @ IF Port, Vdd = +4V nLO mRF -2 -1 0 1 2 55 47 5 44 42 53 18 X -14 42 13 4 3 2 1 0 MxN Spurious @ RF Port, Vdd = +4V nLO mIF -2 -1 0 1 2 IF = 1 GHz @ -10 dBm LO = 19 GHz @ +2 dBm All values in dBc below RF power level. Measured as upconverter X 13 X 5 4 3 2 1 30 36 -20 36 37 3 54 0 RF = 39 GHz @ -10 dBm LO = 19 GHz @ +2 dBm All values in dBc below IF power level. Measured as downconverter 5 - 114 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v01.0803 MICROWAVE CORPORATION HMC339 GaAs MMIC SUB-HARMONICALLY PUMPED MIXER, 33 - 42 GHz Outline Drawing NOTES: 1. ALL DIMENSIONS IN INCHES (MILLIMETERS) 2. ALL TOLERANCES ARE 0.001 (0.025) 3. DIE THICKNESS IS 0.004 (0.100) BACKSIDE IS GROUND 4. BOND PADS ARE 0.004 (0.100) SQUARE 5. BOND PAD SPACING, CTR-CTR: 0.006 (0.150) 6. BACKSIDE METALLIZATION: GOLD 7. BOND PAD METALLIZATION: GOLD 5 MIXERS - CHIP 5 - 115 Pad Descriptions Pad Number Function Description Power supply for the LO Amplifier. An external RF bypass capacitor of 100 - 330 pF is required. A MIM border capacitor is recommended. The bond length to the capacitor should be as short as possible. The ground side of the capacitor should be connected to the housing ground. Interface Schematic 1 Vdd 2 RF Port RF Port. This pad is AC coupled and matched to 50 Ohm from 33 - 42 GHz. 3 IF Port IF Port. This pad is DC coupled and should be DC blocked externally using a series capacitor whose value has been chosen to pass the necessary IF frequency range. Any applied DC voltage to this pin will result in die non-function and possible die failure. 4 LO Port LO Port. This pad is AC coupled and matched to 50 Ohm from 16 - 21 GHz For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v01.0803 MICROWAVE CORPORATION HMC339 GaAs MMIC SUB-HARMONICALLY PUMPED MIXER, 33 - 42 GHz Assembly Diagrams 5 MIXERS - CHIP Mounting & Bonding Techniques for Millimeterwave GaAs MMICs The die should be attached directly to the ground plane eutectically or with conductive epoxy (see HMC general Handling, Mounting, Bonding Note). 50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film substrates are recommended for bringing RF to and from the chip (Figure 1). If 0.254mm (10 mil) thick alumina thin film substrates must be used, the die should be raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab) which is then attached to the ground plane (Figure 2). Microstrip substrates should be brought as close to the die as possible in order to minimize ribbon bond length. Typical die-to-substrate spacing is 0.076mm (3 mils). Gold ribbon of 0.075 mm (3 mil) width and minimal length <0.31 mm (<12 mils) is recommended to minimize inductance on RF, LO & IF ports. An RF bypass capacitor should be used on the Vdd input. A 100 pF single layer capacitor (mounted eutectically or by conductive epoxy) placed no further than 0.762mm (30 Mils) from the chip is recommended. 3 mil Ribbon Bond 3 mil Ribbon Bond 5 - 116 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v01.0803 MICROWAVE CORPORATION HMC339 GaAs MMIC SUB-HARMONICALLY PUMPED MIXER, 33 - 42 GHz GaAs MMIC SUB-HARMONICALLY PUMPED MIXER 17 - 25 GHz Handling Precautions Follow these precautions to avoid permanent damage. Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean the chip using liquid cleaning systems. Static Sensitivity: Follow ESD precautions to protect against > 250V ESD strikes. Transients: Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize inductive pick-up. General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers. 5 MIXERS - CHIP 5 - 117 Mounting The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The mounting surface should be clean and flat. Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 C and a tool temperature of 265 C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 C. DO NOT expose the chip to a temperature greater than 320 C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for attachment. Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer's schedule. Wire Bonding RF bonds made with 0.003" x 0.0005" ribbon are recommended. These bonds should be thermosonically bonded with a force of 40-60 grams. DC bonds of 0.001" (0.025 mm) diameter, thermosonically bonded, are recommended. Ball bonds should be made with a force of 40-50 grams and wedge bonds at 18-22 grams. All bonds should be made with a nominal stage temperature of 150 C. A minimum amount of ultrasonic energy should be applied to achieve reliable bonds. All bonds should be as short as possible, less than 12 mils (0.31 mm). For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com |
Price & Availability of HMC339
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |